Elk skin handlebar, width 7.5 cm, length 57 cm, sufficient for racing and hiking handlebars up to 48 cm wide.
Pre-drilled and delivered with the necessary braid and needles for sewing. With illustrated instructions.
Original, elegant and comfortable!More info & orderRackTireHeadsetBarplugBellBidonBottlecageBrooks spare partsCranksetDecaleurDerailleurmiscellaneousPanniersToolsGripsCableBasketHubHubdynamoPedalPumpBrakeBrakeleverBrake CablesFenderMudflapMirrorsHandlebarBartapeQuillstemHandlebar BagToeclipstrapToeclipBottombracketRimLightShifterStemFrontrackWheelWheelsSaddlebagSeatpostSaddleBrooks saddleBrooks Framebag
Products
Elk skin handlebar, width 7.5 cm, length 57 cm, sufficient for racing and hiking handlebars up to 48 cm wide.
Pre-drilled and delivered with the necessary braid and needles for sewing. With illustrated instructions.
Original, elegant and comfortable!More info & order
These are straight arms that are compatible with our Campeur Racks. They're made from 7mm aluminum alloy rod and are 250mm in length. While they are designed for VO racks, they should work fine on Nitto's offerings as well. You may also need daruma hardware to connect these to your rack.More info & order
The Soto coffee maker is a great little filter holder that folds down small to fit into any handlebar bag or seat bag, and it's light enough that it won't be noticed.
The ingenious design of this filter means that it won't collapse under the weight of water and wet grounds. It is made like a spring, so the default is that it is open. It uses the three base prongs to hold it shut for traveling.
The base pops out to 4.5 inches by 4.1 inches, so it should fit most mugs out there.
Made of stainless steel coil, this 45g filter holder comes with a mesh carrying bag and 10 cone filters. Additional #2 filters can be found at your local grocery store.More info & order
Brooks Handlebar Cap Cambium. Brooks handlebar cap in Rubber from the Cambium series. Intended to be used in combination with handlebar tape. Delivery concerns 2 pieces. Color: Natural or BlackMore info & order
Made of full-grain cowhide like our saddles, these handlebar covers are a perfect addition to handlebars, mud flaps and, of course, saddles.
They have a perfect fit thanks to a screwed silicone end cap.
This version is also available in natural leather, black leather or brown leather.
MTB = ø22.2 & Race ø24.More info & order
These leather toe straps feature anti-stretch material sandwiched between two layers of Australian cowhide. They are glued and then stitched along the edges for durability and an elegant look. They include buckle covers to protect your shoes. Their 450mm length is longer than most straps to accommodate wider American feet.
Sold per pair.More info & order
Don't throw out those vintage downtube shifters - they're the perfect match for city bikes, tourers, and porteurs! They're lightweight, simple, inexpensive, and are compatible with almost any front and rear derailleur. Although, they can be a pain to reach for in traffic.
The VO Thumb Shifter Mounts allow you to mount downtube and bar-end shifters on your handlebars. These thumbies put your shifter within easy reach while avoiding the complexity of brifters. They can even be used on drop bars.
Compatible with any standard road, mtb, and city handlebars (22.2 and 23.8mm grip area)
Hinged design so you don't need to remove any components or accessories for installation
Integrated barrel adjustor to dial in cable tension on the fly
They fit Dia-Compe Downtube Shifters, Dia-Compe Bar End Shifters, Shimano 10/9/8 speed Bar End shifters in addition to a ton of vintage downtube and bar-end shifters
Sold as a pair. Shifters not included.
Note: Not compatible with Microshift shifters (the shifter is too tall) or Dia-Compe 11s road/10s dynasys shifters.More info & order
These lovely brass bells have been made in the same small factory for many decades. They have hammer-type strikers, a beautiful tone, and great resonance.
Compared to our Temple brass bells, the Striker bells are a little louder and a few millimeters wider. Unfortunately, they will not work with our Retro bell mount or Spacer bell mount.
Features a chrome clamp for handlebars.More info & order
These lovely brass bells have been made in the same small factory for decades. They have solid brass domes and use old-fashioned spring strikers that produce a sweet resonating tone. Mount them to your handlebar or quill stem.
Available in brass and mirror finish.More info & order
NITTO CNC ahead stem. Angle 5° (85°), Clamp diameter 31.8mm, Head clamp 28.6mm blackMore info & order
Impact-resistant composite platform pedal with eight removable pins per side.
• Low profile
• Sealed cartridge bearings
• Black, red, or teal blueMore info & order
U-Stay fixing brass, 5mm by allen key. Sold by 4 pieces with 1 allen key, 4 leather washers
More info & order